Shaft power components


Five causes of bearing failure

1 August 2017 Shaft power components

The following five factors can produce their own particular type of damage and leave their own special imprint on a bearing. By examining a damaged bearing it is possible to determine the root cause of the damage so that the requisite actions can be taken to prevent a recurrence.

Electrical erosion

Electric erosion or arcing, can happen when a current passes from one ring to the other through the rolling elements. The extent of the damage depends on the amount of energy and its duration. However, the result is usually the same: pitting damage to the rolling elements and raceways, rapid degradation of the lubricant and premature bearing failure. To prevent damage from electric current passage, an electrically insulated bearing at the non-drive end is usually used. There are two types of insulated bearings available from SKF: Insocoat bearings and hybrid bearings.

Inadequate lubrication and contamination

If the lubricant film between the rolling elements and raceways is too thin due to inadequate viscosity or contamination, metal-to-metal contact occurs. Check first whether the appropriate lubricant is being used and that re-greasing intervals and quantities are adequate for the application. If the lubricant contains contaminants, check the seals to determine if they should be replaced or upgraded. In some cases, depending on the application, a lubricant with a higher viscosity may be needed to increase the oil film thickness.

Damage from vibration

Motors that are transported without the rotor shaft held securely in place can be subjected to vibrations within the bearing clearance that could damage the bearings. Similarly, if a motor is at a standstill and subjected to external vibrations over a period of time, the bearings can also become damaged. Secure the bearings during transport in the following manner: lock the shaft axially using a flat steel bent in a U-shape, while carefully preloading the ball bearing at the non-drive end. Then radially load the bearing at the drive end with a strap. In case of prolonged periods of standstill, turn the shaft from time to time.

Damage caused by improper installation and setup

Common mistakes in installation include using a hammer to mount a coupling half or belt pulley onto a shaft, misalignment, imbalance, excessive belt tension, and incorrect mounting resulting in overloading. To prevent this, use precision instruments such as the SKF shaft alignment tool and Microlog vibration analyser to check alignment and vibration, and also use the appropriate tools and methods when mounting bearings.

Insufficient bearing load

Bearings always need to have a minimum load to function well. The damage will appear as smearing on the rolling elements and raceways. In order to prevent this, make sure to apply a sufficiently large external load to the bearings. It is most important to remember this when using cylindrical roller bearings, since they are typically used to accommodate heavier loads. This does not apply to preloaded bearings.

For more information contact Samantha Joubert, SKF South Africa, +27 (0)11 821 3500, [email protected] www.skf.co.za



Credit(s)



Share this article:
Share via emailShare via LinkedInPrint this page

Further reading:

Next-gen battery-driven grease gun
SKF South Africa Other technologies
SKF’s innovative TLGB 21 battery-driven grease gun optimises lubrication efficiency and reduces costs, by seamlessly combining advanced technology with a smart, rugged design.

Read more...
The importance of original branded bolt securing products
Bearing Man Group T/A BMG Shaft power components
BMG is concerned about the proliferation of counterfeit merchandise, and the dangers associated with using inferior goods.

Read more...
Advanced solutions for valves
Bearing Man Group T/A BMG Shaft power components
BMG delivers state-of-the-art valve solutions to diverse industries across Africa, in collaboration with InterApp, a global leader in the design and manufacture of high-quality valves.

Read more...
Monitoring the health of systems
SA Gauge Editor's Choice Shaft power components
Pressure and temperature gauges are vital instruments in various industries. However, they are susceptible to failures that can compromise their accuracy and reliability. When these gauges fail, the consequences can be severe.

Read more...
Cogged raw edge belts
SKF South Africa Shaft power components
SKF’s cogged raw edge belts are ideally suited for essentially any industrial application that runs on ISO wedge and classical V-belt pulleys.

Read more...
The torque of the town
Shaft power components
Bolt and Engineering Distributors (B.E.D.) is pleased to announce its new distribution agreement with torque and tensioning company Bolt Torque, which has a comprehensive range of manual, hydraulic, electric and battery bolt torque, and bolt tensioning solutions.

Read more...
Taking reliability to the trenches
SKF South Africa Shaft power components
SKF’s maintenance-free Y Bearing Unit has significantly extended equipment uptime for key customer Gibela, a leading level 5CE CIBD-rated civils company with more than ten years of experience in the field.

Read more...
Quick couplings to prevent leakage
Shaft power components
Research and development in the quick coupling industry is advancing beyond functionality, and is focusing on manufacturing leak-free quick couplers which also minimise impact on the environment.

Read more...
Nord-Lock’s CE marked securing washers
Bearing Man Group T/A BMG Shaft power components
The Nord-Lock range of securing washers, distributed and supported by BMG, is the only brand on the market that currently displays the CE quality mark of approval from leading global authorities.

Read more...
Navigating the cosmos with precision
SKF South Africa Shaft power components
As the next-generation Very Large Array navigates towards its key science goals, SKF’s technology is playing a pivotal role in charting the stars. SKF is providing key components for the next-generation Very Large Array (ngVLA), a $2 billion telescope system that aims to peer deeper into the universe than ever before.

Read more...