Refrigeration air dryers are very reliable and provided they are correctly selected for the application and installed correctly will give many years of service. Dryers have to be re-rated to operate in South Africa’s high inlet and ambient temperatures and the manufacturer’s design flow rates have to be reduced to keep the thermal load in balance. If operating pressures are lower than 7 bar this also reduces the dryer’s flow capacity. Here are a few rules that should be followed.
Check the condensate drain valve daily. Clean out the strainer, if fitted, every month or as often as necessary. Do not hard pipe the drain valve to the drain system. You can’t see if the drain’s working. Pipe it up with a 30 cm long clear 10 mm diameter sacrificial hose along with push-in fittings. If installed in this manner you can see the drain working and you can unplug it to really see what is happening if you need to.
A dryer with a blocked drain is a water generator, not a device for water removal. The use of a low cost dew point monitor will tell you instantly if the dryer has a blocked drain valve or has a technical problem as it measures the actual water content in the air stream.
Keep the air-cooled freon condenser clean and free from dirt.
Do not use a high pressure power washer, it will bend the fins and cut off the cooling air flow. Reverse blow the condenser with clean, dry 3 bar compressed air as often as necessary to keep it clean. Your site conditions will influence the frequency.
Observe the dew point temperature gauge on the front fascia of the dryer daily, it must read 3°C ±2.
On too many occasions we see dryers in a tripped state, or not even turned on, so it’s vital to train your compressor room operators so that they understand what the normal dryer status indicators are. High pressure freon pressure tripouts are common, especially in summer. The cause of this trip can be:
• Dirty freon air or water cooled condenser.
• Insufficient cooling water flow and/or water cavitations.
• Air volume overload and/or machine undersizing.
• Internal freon compressor thermal overload caused by thermal overload.
• Poor compressor room ventilation.
• Poor positioning of the dryer in a hot air flow generated by compressor coolers.
• Freon HP trips are especially common on full feature air compressors with built-in air dryers. They need special attention and monitoring or dewpoint performance will suffer.
Finally place the dryer under cover or in a well-ventilated compressor room, they are not designed to work when exposed to the elements.
Refrigeration dryers perform a fantastic service and will keep a system clean and dry for years on end, provided you follow these rules. For those that are in the process of designing or reconfiguring a compressor room, why not visit the educational section of the Artic website and download Hints And Tips For Compressor House Design for a few extra ideas.
Compressed air treatment do’s and don’ts Artic Driers International
Editor's Choice Pneumatic systems & components
As a long-established importer and manufacturer of air dryers, Artic Dryers often sees the results of poor installation and issues with aftercoolers that create serious problems in air drying systems.
Read more...Next-gen air compressors for plastics manufacturer
Pneumatic systems & components
Integrated Air Solutions has reinforced its partnership with global compressor manufacturer, ABC Compressors by facilitating the installation and commissioning of two next-generation direct-drive ABC machines for a prominent plastic manufacturer in South Africa.
Read more...Acoustic imaging detector for gas leaks and partial discharge Artic Driers International
Hydraulic systems & components
The new SUTO iTEC S532 acoustic imaging detector provides an easy and effective way to locate pressurised air and gas leaks and partial discharge (PD) in industrial high-voltage environments.
Read more...Seamless compressed air supply
Pneumatic systems & components
The efficient performance of compressed air systems is the foundation for seamless production processes and sustainable business. The adoption of a comprehensive service plan delivered by an OEM like Atlas Copco is key to overall compressor performance, efficiency, reliability, and long lifecycle.
Read more...Selection of two-port valves: an open and shut case SMC Corporation South Africa
Pneumatic systems & components
Little consideration is generally given to two-port valves because they are often perceived as simple devices that only open and close to control downstream fluid supply. Although this is mechanically true, choosing the optimal two-port valve for your application can make a big difference, saving space, weight and energy consumption.
Read more...Integrated Air Solutions expands its compressor rental service
Pneumatic systems & components
The significant growth of the industrial air compressor rental division launched by Integrated Air Solutions under a year ago, has prompted the need for more resources and equipment. Headed up by Rudolf ...
Read more...Thor’s hammer of pneumatic knockers Neu Matics SA
Pneumatic systems & components
Neu Matics acts as sole distributor for a range of internationally recognised brands, and one of these is the pneumatic knocker from singold.
Read more...Compressed air drying and monitoring with low dewpoints Artic Driers International
Pneumatic systems & components
Artic Driers manufacturers the Sahara low dewpoint, heatless pressure swing air dryers with SANS 347 pressure code. These desiccant-rich pressure dryers comfortably obtain pressure dewpoints of -40°C.
Read more...Tyre-actuated globe valve Parker Hannifin - Sales Company South Africa
Pneumatic systems & components
Parker Hannifin has launched a tyre-actuated pneumatic valve in its Bestobell cryogenic globe valve range. The valve can be operated remotely with a single switch command, providing much greater speed and convenience than a manually operated type.
Read more...Oil-free beer and wine processing
Pneumatic systems & components Hydraulic systems & components
The food and beverage industry depends on superior quality, 100% oil-free compressed air to eliminate the presence of unwanted oil vapour throughout the production line.